iflight Taurus X8 Pro 8S HD Cinelifter w/ DJI Air Unit – BNF

• The estimated flight time is 12 Minutes without a camera and 6-8 Minutes with the camera
• Universal camera mount and accessories for a wide range of cameras to install
• Optimized CG through the adjustable camera and battery mount
• Big XING2 3100 motors with extreme lift and flight performance
• 8x single X-Class grade ESC motor drivers for more reliability
• 2kg max payload for various cinema and DSLR cameras
• GPS flight data and rescue functionality pre-installed
• Redundant ESC and motor configuration
• 8S Power System

SUPPORTS LARGE PAYLOADS

This iflight cinelifter supports 2kg of maximum payload for a variety of top-mounted cameras and the ability to fine-adjust the stable mount for a perfectly balanced CG (Center of Gravity). The top mount 8S battery acts as a power source as well as a counterweight for most common cinema camera weights which can be easily exchanged with our iFlight battery quick-release mounting system. The adjustable CNC aluminum camera mount offers angles from 5 to 35 degrees and can be safely secured for reproducible outcomes. No jello, no jitter, no problem; Our silicon-ball dampened carbon camera base is decoupled from the rest of the frame to reduce the amount of vibration generated by motors and propellers. For the perfect cinematic shot, we recommend additional software stabilization in the post (Reelsteady, Gyroflow, etc.) or a hardware module (for example SteadXP).

PRE-TUNED AND PRE-SETUP

• Don’t worry about tuning, we did that for you already! A basic PID – and Filter tuning were applied for a great flight experience!
• Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn’t end in a mess!
• To restore lost tunes or updates, please check our linked article on “Firmware/Factory Dumps”
• GPS Rescue is ON by default. Please check our linked article on “GPS Rescue Mode // Setup”
• Please check our linked article on “How to disable Angle-Mode, activate Acro-Mode”

• Receiver Options: DJI PNP or TBS Crossfire Diversity Nano RX
• GPS module: iFlight M8Q-5883-GPS & Compass V2.0 (LINK)
• Total Dimensions: 430mm*350mm (body dimension)
• Max Speed: 160km/h (13km/h with high payload)
• Flight Time: 6-8 Min (12 Min with no payload)
• Payload: 1-2kg (1-1.5kg is recommended)
• Upper(middle) plate thickness: 3.5mm
• Weight: 2.3kg±5g (without battery)
• Bottom plate thickness: 3.5mm
• BLITZ F7 Pro Flight Controller
• Motor: XING2 3110 900KV
• Top plate thickness: 3mm
• Arm Thickness: 8mm
• Propeller size: 8 inch
• Wheelbase: 450mm

BLITZ F7 PRO FLIGHT CONTROLLER

• Mount pattern: 35*35mm / 4mm PCB hole diameter
• Smart Audio / IRC Tramp VTX protocol supported
• Firmware target: IFLIGHT_BLITZ_F7_PRO
• BlackBox: 512MB Onboard
• Dimensions: 41*41.5mm
• BEC: 5V/2.5A, 12V/2A
• Barometer: DPS310
• OSD Chip: AT7456E
• LED controller: Yes
• MCU: STM32 F722
• Weight: 17g (±2)
• Beeper pad: Yes
• Gyro: MPU6000
• UARTS: 6

iFlight ESC COMMANDER PCB (8X SUCCEX X80A)

• Supports up to Dshot600, Proshot, Oneshot, Multishot
• Firmware Target: iFlight-BL32-PRO
• Up to 48kHz PWM frequency
• Mounting pattern: 40*17mm
• Constant: 80A / Burst: 100A
• Capacitance: 470uF/35V
• BlHeli32 telemetry: Yes
• Current Sensor: Yes
• Input: 2-8S LIPO
• Weight:8.1g
• MCU: F051
• BEC: No

Includes